Automation for sliding doors, designed to make your life easier
Ditec DAS107PLUS is the new sliding door operator able to satisfy all requirements in standard commercial environments with frame weight up to 160 kg.
Designed to be easy and fast to install, Ditec DAS107PLUS is the perfect choice for professionals in door automation who look for low inventory cost and ease of maintenance.
QUALITY & RELIABILITY
Ditec DAS107PLUS is the new sliding door operator focusing on the needs of our customers and featuring high quality components at the right value:
- Performing electromechanical operator for up to 160 kg door weight
- Tested up to 1 Million cycles
- Long-lasting automation with 24 V DC DUNKERMOTOREN™ with built-in Encoder
- Reinforced techno-polymer wheels in DUPONT™ Delrin®
- Fully certified and tested by TÜV SÜD
TIME SAVING INSTALLATION
Designed for a simple and efficient installation, few components to assemble and few steps to set-up. Ditec DAS107PLUS is the time saving solution for any need:
- Plug & Play connectors
- Automatic self-learning start-up mode, with auto detection of:
– weight of wings
– passage opening
– presence of locking device and typology (fail safe, fail secure)
– emergency and back-up batteries
- Easy and accurate CU setting with digital programming and just few key parameters
- Switching power supply covering a wide range of electric voltages (100 V÷240 V; 50/60 Hz)
- Easy adjustment of trolleys and belt
Technical data:
- Gearmotor: 24 V DC with encoder
- Power supply: 100 V ÷ 240 V 50/60 Hz
- Max nominal power: 75 W
- Auxiliary power: 0.64 A @ 24 V DC
- Operating temperature: -20°C / +50°C
- Protection rating: IP20
- Dimensions (H x D x L): 120x140xL mm
- Max operator lenght: 6650 mm
Frame systems
Ditec pam30
The PAM 30 series consists of aluminium profiles for 1 wing, 2 wings or telescopic automatic sliding doors, with fanlights and fixed walls, which positions itself between the PAM 16 and the ALU48 series. It is far sturdier then the PAM 16 series and can hold 8 to 23 mm thick glazing, whilst it is far thinner than the ALU48 series.
Distinctive features of the system
PAM 30, designed to be compatible with current and future automations, consists of a set of visible reduced sections, 30 mm thick profiles.
By using 3 different types of seals, it is able to hold 8/9 mm, 10/11 mm e 22/23 mm unbreakable glasses; supplied in the mill finish and anodised aluminium (EURAS C0) version.
It is also fitted with an adjustable, floor recessed guide, suitable for 1 or 2 wings sliding openings and telescopic openings.
Benefits
The PAM 30 series ensures several benefits, such as:
- very easy machining, assembly and installation ensured by: 90° cuts, self-threading screws;
- full compliance with safety international standards;
- alignment of top and bottom crosspieces;
- side closure between wings and frame separated by a pressure seal;
- centrally closed wings with dual stop, dual snap-on seal;
- photocells inserted between the fixed panel or in special wall mounted profiles, when wings only are fitted (only countries outside the EU);
- profiles with totally smooth visible front, with no grooving;
- in the wing bottom section lower profile housings are available to allow runner operation and to insert the floor seal brush.
.
Ditec alu48
The ALU48 series is an aluminium profile system specifically designed to make up frames with very quick and simplified machining, installing and commissioning operations.
The system is dedicated to 1 wing, 2 wings or telescopic automatic sliding doors, including those with fanlight and fixed walls, in the standard version and in the wing breakout anti-panic or full breakout versions.
Distinctive features of the system
ALU48, designed to be compatible with current and future automation systems, includes a range of 48-mm-thick profiles, equipped with large vertical profiles, with sturdy visible sections, for all Standard, Telescopic, Transom and Wall types. Prepared to house various types of locks for closing the mobile wings.
The system can accommodate all types of glass, from 8-40 mm thicknesses, without protruding frames. It comes in mill finish or anodised (EURAS C0) aluminium bars. As an alternative, it has an adjustable floor guide track that is suitable for both 1- or 2-wing sliding and telescopic entrances.
Benefits
The benefits ensured are listed below:
- the fixed components can be installed with self-compensating profile for the surround;
- easier offset of any installation errors;
- the fixed panels are fully independent;
- identical assembly screws are used, ensuring a faster operation;
- simpler machining operations as the wings and fixed panels can be cut at 90°;
- the bottom and top crosspieces can be aligned;
- the wings are centrally closed with a double stop, double slot-in seal;
- the profiles are smooth, without grooving;
- better seal with special brushes.
